LOVELY FLORAL HEADBAND

WHAT YOU’LL NEED:

-lace

-synthetic flowers

-elastics

-glue stick

-needle & thread

STEPS:

-First, let’s do the headband. Measure 30 inches and cut

-Fold into half

-Insert the elastics and stitch to hold in place

-Do a loosely overlapping twist

-When you get to your last twist, glue stick each intersections.

-Again insert the other end of the elastic and stitch the tail end of the lace.

-Now that we’re done with the headband, we can now attach the flowers.

-Glue stick each flowers onto the intersections.

-Let the glue stick dry.

-Done!

EMBELLISHED BLAZER

WHAT YOU’LL NEED:

-plain blazer

-studs

-fabric glue

STEPS:

-Using the fabric glue, stick each stud on of the front edge of the blazer.

-Continue to create a line.

-Do it on both sides and wait for a few minutes or until the g lue gets dry.

-DONE!

http://stylecraftbycherry.blogspot.com/

COLLAR ACCESSORY

WHAT YOU’LL NEED:

-chain

-stones

-clipper

-glue stick

-jump ring

-long nose and cutter pliers

STEPS:

-Attach the jump ring to the clipper. Do it in both clippers.

-Add the chain to the jump ring onto the other side of the jump ring and back to other side to create a two layer of chains.

     -12cm. (upper chain length)

     -16 cm. (lower chain length)

-Now embellish the clipper with a stone (or any of your choice). Adhere using glue stick.

-DONE!

http://stylecraftbycherry.blogspot.com/

LOVE WIRED RING

WHAT YOU’LL NEED:

-gold aluminum wire

-thin wire

-long nose and cutter pliers

-jump ring

-small beads

-heart plastic stone

STEPS:

-Create a small loop using the gold aluminum wire and long nose plier.

-Twist carefully to make letters: L O V E

-Small loop again and cut.

-Attach the thin wire in the small loop.

-Insert each small bead until you reach your desired finger size.

-Wrap it around in a perfume nose to attain a perfect round ring.

-Got your ring size? Brace the thin wire around the small loop to lock.

-For the finishing touch, attach the jump ring to the heart stone and dangle at the letter V.

-DONE!

http://stylecraftbycherry.blogspot.com/

RIBBON ROSE HEADBAND

WHAT YOU’LL NEED:

-satin and organza ribbon

-piece of white fabric

-plain headband

-needle and thread

-glue stick

-marker

-scissors

STEPS:

-Two ribbons are used here for more dimensions. First, get your satin ribbon and fold in half.

- Cut the fabric in circle (diameter depends on the size of the flower)

-Mark the center of the fabric.

-Anchor the satin ribbon at the center.

-Create a bud like by stitching in a round path.

-Now add the organza ribbon and stitch along with the satin ribbon.

-Continue stitching in a circular trail until you reach the edge.

-When done in stitching, you can now attach your rose ribbon to your headband using a glue stick.

-DONE!

http://stylecraftbycherry.blogspot.com/

SEQUINED COLLAR NECKLACE

WHAT YOU’LL NEED:

-sequined lace

-felt cloth

-black satin ribbon

-fabric glue

-paper pencil

-ruler

-scissors

-pins

STEPS:

-Draw a collar like figure on the paper.

-Trace or pin it on the felt cloth.

-Do on both sides and cut.

-Stitch the center ends of both sides to be one.

-Using the fabric glue, stick the sequined lace on the felt cloth.

-Fold the ends if necessary.

-Not to forget to insert the satin ribbon in both ends and stick.

-DONE!

http://stylecraftbycherry.blogspot.com/

WIRED BAND

WHAT YOU’LL NEED:

-aluminum wire

-fabric

-tape measure

-ruler

-pencil/ marker

-scissors

-thread & needle

-pins

STEPS:

-On the wrong side of the fabric, measure 33 inches: length and 3 ½ inches: width

-Fold in half and pin the edges.

-Cut.

-Measure ½ inch.  Mark. (Note: Both tips must be a pointy curve line)

-Stitch following the mark. Make sure to leave a small space (½  inch) at the middle, this will serve as a door for flipping the fabric and entrance of the wire.

-When done in stitching, flip the fabric and insert the measured wire (33 inches).

-DONE!